壓縮空氣管道安裝程序

   質料出場——質料查驗——支架制作——支架安置— —管材下料——坡口加工——焊接或螺紋加工——配件組裝——地面組裝——就位——毗連——牢固—— 吹掃、試驗辦法準備—吹掃—強度試驗—精密性試驗 ——泄壓——防腐施工—正式通氣。

壓縮氛圍管道安置要求

   壓縮氛圍管道可接納焊接鋼管或無縫鋼管管道，彎頭應盡量接納煨制彎頭，其彎曲半徑不該小于公稱直徑3倍，橢圓度不大于8%。管道經切割、鉆孔與焊接完畢后，管內應清理潔凈，不容許留有金屬熔渣，渣滓物及其他臟物。 管道體系中全部支、吊架安置應牢固、位置準確，無歪斜，松動現象。豎直安置的管道應垂直，長度在 4m 以上時容許傾斜 12mm，在 4m 以內時容許傾斜 4mm， 安置的管道應有一定的坡度，其坡度大小不得超過0.0005。管道安置完畢應用壓縮氛圍吹洗，吹除管內臟物。 管道外貌一樣，通常先涂刷 1-2 遍防銹漆，再涂刷一遍淺藍色調合面漆，埋地管道應刷瀝青漆。下料、憑據圖紙尺寸決定現實安置管段長度，并在材料中按安置長度截取管段，稱為下料。圖紙中通常都不標注安置長度，而只給定了部件、轉點、支架定位用的相對尺寸，所以只能憑據圖紙尺寸盤算出下料長度。 螺紋毗連的管段下料長度、圖紙尺寸減去配件中必須有管道部分的長度，也可以按管道在兩配件連接間的長度加上螺紋的長度來盤算。 焊接下料長度、圖紙尺寸減去配件長度和焊縫間隙，必要時再加上焊縫收縮量。 法蘭毗連的管段下料長度，圖紙尺寸減去法蘭厚度， 如一端法蘭，則應減去法蘭厚度的 1/2. 為取得安置管段，用鋸、氧-乙炔焰切割、機器切割等方式，在管材上截取，安置管段的管口必須平整，無毛刺等缺陷，若有缺陷，應用銼刀、管口刮刀及砂輪等東西進行修整。